[100% Fix]: Ethernet Doesn’t Have a Valid IP Configuration Issue

Ethernet doesn’t have a valid IP configuration. Troubleshoot: Suppose you’ve recently reinstalled Windows and are booting up on your PC and getting unidentified in the network that has no internet access. This is a severe, regular problem that can occur.

It tends to be very overwhelming for certain users to Assaf or make this post to tell you the best way to resolve the “Ethernet doesn’t have a valid IP configuration.”

Fix Ethernet Doesn’t Have A Valid IP Configuration in Windows

Presently, you can see here(See the Picture). I’m simply going to run the troubleshooter immediately. The error message that you will see is presumably the better-known error message you’ll see here. So let this simply finish. Also, we’ll see what the error message says you can see: “Ethernet doesn’t have a valid IP configuration and not fixed.”

Also, no matter what you attempt to do inside here won’t be ready to fix it that simply. Also, I’ll show a few stages that I’ll take to try to determine this issue.

What’s the significance here if my PC says the ethernet doesn’t have a valid IP configuration?


You likely have your IP setup set to static; this is for additional and advanced configuration of complex networks, routed and switched in various PCs. Your IP possibly was composed wrongly, or it coordinates with the IP utilized by another PC. 

This can regularly be resolved by setting your IP configuration to Automatic or Dynamic.

Indeed, that obviously shows that there is certainly not a working connection. 

All in all, what can be incorrect? 

The plug cable or one of the ports could be terrible. That could prompt these errors. Probably not going to be the ports.

Or, on the other hand, it very well may be that the router has a WAN ethernet port, and you’ve connected to that. The router or attempting to be a client and connect with an upstream network. Thus, it isn’t attempting to configure a network (Ethernet doesn’t have a valid IP configuration).

So, the principal thing to attempt is to move the router end of the cable to an alternate port if you can. At that point, attempt an alternate cable. 

From that point onward, there could be a major issue with the router arrangement. That gets confused, so you’d need to sign in and investigate.

How to Fix Ethernet Doesn’t Have a Valid IP Configuration – Windows 10/8/7


Solution #1, Change The Sleep Settings


1st, The following thing you have to do is go down to the search box at the base left-hand corner of your screen. 

click on The Sleep Settings Ethernet Doesn't Have a Valid IP Configuration

2nd, And type the word power. Now, you need to open up the “Power and Sleep settings.”

3rd, You have to click on “Additional power settings.” 

choose what power do

4th, Now, You have to click on “Choose what power button does.”

5th, Also, you need to tap on “change settings that are currently unavailable.” 

uncheck fast startup option

6th, We have to uncheck the “Turn off fast startup” option and “Save Changes.”

Now you need to close down all the windows. Here, you can see that your network adapter still hasn’t found an IP address or anything. so it’s as yet not working. 

Whenever you have turned everything off, hold it for around 30 seconds. You would then be able to switch everything back on. Also, Fingers Crossed, The Ethernet Doesn’t have a valid IP configuration in Windows 10 problem is gone. You will currently have internet access. Also, as of now, in my case, I have web access again, which means it worked for me.

Solution #2: Reset Your IP address With CMD


I’m demonstrating how to reset your PC’s TCP/IP and your windsock stack in Windows 10. Your setting both of these can fix your web connection relying upon the issue. 

Generally, when I do this is. At the point when I know my router is working. Be that as it may, my PC says I have no internet access. Before doing this, you need to ensure that you are logged into the administrator account on your Computer. If you are, definitely not. This won’t work.

CMD Commands To FIX Network Problems:

1st, Hold down these keys: “Windows” and press the letter “X.”

2nd, Left click on “Windows PowerShell(Admin) or Command Prompt (Admin) “.

3rd, Left click on “Yes” in the “User Account Control” permission  Window.

You now need to type in three Commands:

1)The first command is:

ipconfig /flushdns

You need to press Enter.

2) Once you’ve done. That one, you now need to type in:

netsh int ip reset 

Press Enter again. 

 3) And you now need to type in their:

netsh winsock reset

Press Enter.

Whenever you’ve done this, now you have to restart your PC once more, which I’m feeling free to do now. Once you have done restart your PC. If you are still getting the “Ethernet doesn’t have a valid IP configuration and not fixed” error, you need to follow the next solution.

Solution #3, Enabling or Restarting DHCP


DHCP is a network element that assigns the IP address to a PC. So the issue of “ethernet doesn’t have a valid ip configuration” can be happening due to deactivated DHCP. To determine the problem, It would help if you enable the DHCP.

1st, Head over to the Network icon (In my case, Wi-Fi) on the base-right side.

2nd, Right-click on this icon. A menu will open. Select the “Troubleshoot problems” option.

3rd, A new troubleshooting window will open.

4th, Select the network troubleshooter option. And click on the Run the troubleshooter option.

5th, Now, you need to follow the instructions.

Now, Restarting the DHCP Service

1st, Need to press the Windows + R on your keyboard and type Services. msc.

2nd, Press the Enter key from your keyboard.

3rd, At that point, the Services window will open.

4th, Scroll down a little bit. Navigate the service named DHCP Client. Then, double-click on it.

selct startup type as automatic

5th, A pop-up window will open. Find the Startup Type select box. Select Automatic from the dropdown.

6th, Now Save the settings by clicking on the Apply and OK buttons.

restart the DHCP service

7th, After that, You have to right-click on DHCP Client service. Select Restart from the contextual menu.

8th, At last, click on Yes to confirm.

Check again if the problem carries on or not.

Read More: How to fix This Site Can’t Be Reached or err_connection_reset” Error?

Solution #4: Unplug and Plug the Router Cable


1st, You need to Power down the PC. 

2nd, Unplug both your Router & your Modem

3rd, You need to hold for at least 30 to 40 seconds.

4th, Now you can plug the modem back into Power. 

5th, Please wait till your CPU lights are solid or the model is correctly loaded. Sixty seconds is recommended. 

6th, Now, Time to plug in the Router back.

7th, Hold on for at least 2 minutes or until it’s fully loaded up. 

8th, At last, Power on your PC back. And check if the Ethernet doesn’t have a valid IP configuration issue is resolved or not.

Solution #5, Regedit Setting


type regedit and click to Registry Editor

As a matter of first importance, you have to go to your Start menu, type over there Regedit, and press Enter from your keyboard. After that, click on Yes to give authorization for user control. 

OR

Additionally, you can go through your Run box by simply squeezing the Windows + R button together from your keyboard. Also, you can see this Run box. Also, after that, you need to type over their Regedit. And it would help if you press ENTER. So you can see the same window.

open those following folder

1st, Now, what do you have to do? You need to expand the HKEY_LOCAL_MACINE file from the left-hand side.

2nd, And after that, expand the SYSTEM file. Now, you need to expand the CurrentControlSet file.

3rd And next expand the Control file.

open Nsi file

4th, And now, you need to scroll down, and you have to find over there NSI. You need to expand the folder.

5th, After that, expand. You can see a bunch of files. Expand the first one.

6th, Now right-click on 26 named files. Select the Permissions option.

check the Full control checkbox

7th, And after that, you can see a new pop-up window. So now, what you have to do, you need to click on Full Control (Under Permissions For Everyone). Check this option in the Allow column. 

8th, And at last, click on the Apply button. Then click on the OK

Now restart your system and check whether your Ethernet doesn’t have a valid IP configuration issue is gone or not.

[inhype_block type=”postsgrid7″ block_title=”Look at this” block_subtitle=”Recommended” block_posts_type=”random” block_categories=”6″ block_posts_limit=”4″ block_posts_loadmore=”no” block_posts_offset=”0″]

 Solution #6, Reset Network


So, if you have any network connectivity issues, you can’t see the impacts. This part will be for you. So, there is a built-in network troubleshooter that we will attempt. Furthermore, run it first. And afterward, we’ll go into how to reset your network settings. So we’re going to bounce into it. 

1st, We will begin by opening up the Start menu. Also, you need to type in settings. The best man ought to be trusted in in-store applications. You need to open that up by left-clicking on it.

2nd, And presently, you need to left-tap on the Network and Internet tile

3rd, On the left side here. We’re under the Network & Internet section. You need to ensure you’re in the Status area. 

4th, Presently, on the right-hand side. You need to look down until you get to the button that says Network Reset or the hyperlink. Left-click on it. 

On the Next Window, it should say:

“This will remove then reinstall all of your network adapters. and set other networking components back to their original settings. You might need to reinstall other networking software afterward, such as VPN clients offer or virtual switches. your PC will be restarted.”

5th, Left-click on the “Reset Now” button there. It will ask, “you sure you want to reset your network settings?”—Left-click on the Yes button. 

You need to close it at this point. I suggest closing off all windows as well as restarting your Computer. Furthermore, ideally, your Ethernet doesn’t have a valid IP configuration issue that has been settled.

Read More: [Modern Setup Host] How To Get Rid of High Disk Usage Issues in Windows 10

 Solution #7, Update Network Driver


Step-by-step instructions to install or update the latest Network Drivers to your Windows 10 System. 

Suppose you go down to the search box at the base left-hand corner of your screen. Type in the device manager in the search box. And open up the Device Manager.

And afterward, go down and find Network Adapters. Also, right-click on your Network Adapter (for my case, Realtek Ethernet adapter). A pop-up will open. What’s more, select the Properties option.

Update your driver

And, if you presently click on the Driver TAB. As you can see, windows 10 just detects the latest driver date as 10:04 2015. yet this isn’t the situation. 

There is a newer version form of the driver that Windows 10 won’t recognize. Simply press Update Driver to get this driver.

Solution #8, Change Your DNS Setting In Windows 10


You have to change your DNS server settings on your Windows 10 operating system. So, prior to setting the DNS server on your Windows 10 operating system. You need to choose which DNS server you need to set on your Windows 10 OS.

So what you need to do is. You need to visit this site. Free and Public DNS Servers.

Here, you can pick your primary DNS server provider and secondary DNS server provider. So you can see there is a rundown of DNS server providers here. Also, we need to choose one of them.

So whenever you have chosen which DNS server, you need to browse here. 

Now, what you need to do is:

1st, You need to simply go to your search bar on the desktop and search for the control panel.

click on Network and Sharing Center option

2nd, Then snap on the Control Panel here. What’s more, when the Control Panel opens. You simply need to search for Network Sharing. So, just write the word networks. And at that point, search for it. Also, most likely, the first result will show up. 

Select the result that says Network and Sharing Center.

At that point, you will actually be able to see another window interface. Presently, I am utilizing the LAN cable for the internet connection (In any case),

click on your connections link and select properties

Suppose you are utilizing a Wi-Fi internet connection. This will likewise show up here. So, right now, I can see Ethernet here. For your situation, it will be the name of the Wi-Fi network. 

3rd, I will simply click on the blue link here. And afterward, I will simply tap on the Properties.

4th, And afterward, in this Ethernet property window. I will simply pick Internet Protocol version 4, and here you can see your Server setting

So, by default, your Windows 10 operating system will detect the DNS server consequently; however, if you want to select it manually.

5th, you have to select the radio button option called “Use the following DNS server addresses.” 

This is the preferred option also because it’s going to make your internet a little bit faster. 

Free and Public DNS Server link

And then, you need to visit the website (I Mentioned the link above). And we are going to set up the DNS server, which is provided by Google (See the picture). 

Change your DNS server addresses

 So we are going to just write for the Preferred DNS server: 8.8.8.8. 

And then the Alternate DNS server is 8.8.4.4 here. 

Once you do that, you can also click this option, which says “Validate settings upon and exit. “

And then it’s going to validate your settings.. . so I’m going to just click on the OK button. And then close this window.

Now you have to Restart your PC, and this step clears your Ethernet doesn’t have a valid IP configuration issue.

Read More: Reboot and Select Proper Boot Device Error | How to Troubleshoot?

Solution #9, Disable/Enable Your Connected Network 


1st, Open the start menu and type the control panel.

2nd, Open your control panel open. Open Network and Internet. Open Network and Sharing Center

Disable the network

3rd, Click on your internet adapter blue link. and Select the Disable option. 

4th, Now, click on the Change adapter settings on the left-hand side. 

5th, Right-click your disabled internet adapter. Select the Enable option.

Now your Ethernet doesn’t have a valid IP configuration problem should be fixed,

Solution #10, Uninstall Driver 


1st, Go over the Windows search and type the word “device manager.”

2nd, Click to open your Device Manager.

3rd, Expand the Network Adapters option.

4th, Right-click on your Network Adapter Driver.

5th, Select the Uninstall device option.

6th, Then a little dialogue box will open. Just press the Uninstall option.

Now Restart your PC and check if the Ethernet doesn’t have a valid ip configuration problem is gone or not.

Solution #11, Restore Your Computer 


1st, Head over to the search box and type Recovery Options.

search for recovery option

2nd, Click on Open Recovery Options.

Click on Restart Now

3rd, Once it opens, On the “Advanced startup” section, and click on Restart now.

4th, Now your System will start restarting. Here, you can see troubleshooting options.

Click on Advanced option on Troubleshoot

5th, Click on Advanced Options again.

6th, On the next screen, You need to click on the System Restore option. Then, It will show you a loading screen.

click on System Restore Options

7th, Afterwards, a Restore point window will open. Just choose your Latest Restore Point and click on the Next button.

Then, click on the Finish button. Now, a confirmation dialogue box will open. Just click on Yes to continue.

Now your PC is restored. It might take a few minutes. I believe your system’s Ethernet Doesn’t Have a Valid IP Configuration is resolved.

Ethernet doesn’t have a valid ip configuration FAQ


How would I connect the PC to an ethernet cable if troubleshooting comes up as ‘local area connection doesn’t have a valid IP configuration’?

DHCP service is neither accessible nor configured. For this situation, your home router should give DHCP services. Thus, your PC is auto-relegated with an IP that starts with 169.Something (also known as APIPA). 

Check if the PC and router are genuinely associated appropriately. Likewise, check if the router has DHCP service enabled as well. On PC, ensure NIC is set to auto rather than manual.

How would I fix “Ethernet doesn’t have a valid IP configuration” on Windows 10? 

The first thing is to have your Ethernet cable safely plugged in. You could have a flawed ethernet port or connector on your PC. Go to the Device Manager, go to the Networks, and uninstall the ethernet driver. And then restart Windows. So it will reinstall the driver. 

If none of this works and you are certain that the source of your ethernet is acceptable, at that point, if you have a PC, you can purchase a modest PCI or PCIe to ethernet connector, which will give you a known working ethernet on your PC. If it is a PC. You can purchase a USB to ethernet adapter.

Other: “local area connection doesn’t have a valid ip configuration”? 

I had this same issue, and it vexed me with no closure. I even attempted an extra NIC. However, Win 8.1 wouldn’t remember it. On eliminating it to check seating, I flipped the PSU power off to close everything down. 

I turned everything to remember that I plugged the mobo NIC back in, and it resolved the problem! I contemplated whether shutting all power permitted the NIC to reset itself completely. 

Worth an attempt; it was the solution for me!

Is there any strategy to figure out if the Ethernet doesn’t have a valid IP configuration? 

To figure out this issue, you should simply follow some of the specific ways. If this thing is figured out how to deal with it correctly, this error will be figured out. Initially, you need to restart your Computer or laptop.

Likewise, go with a router or modem. On the opposite side, you can likewise clear the network cache.
Indeed, even you can temporarily turn off the antivirus whenever. Particularly, with regards to taking care of this issue, you have to follow these things for a better result all in all.

Leave a Comment